If you looking for frsky x4rsb then you are right place. We are searching for the best frsky x4rsb on the market and analyze these products to provide you the best choice.
Reviews
1. iFlight 150mm 2.4G Receiver Antenna Generation 4 RF113 (smaller) IPEX Port for Latest FrSky X4R-SB Receiver and Remote Controller ( pack of 20pcs )
Feature
RF-113 Silver-plated feeder cableIPEX 4 Generation interface
Precision machining,Low loss signal stability
A must have for Frsky XM+ and X4R rx/tx field repair
Smaller ipex connector type fit for new FRSKY X4R-SB receiver
Description
2.4G remote control, surveillance, model aircraft, receivers, Bluetooth and other antennasUse: Vehicles and Remote Control Toys
Frequency:2400-2500 MHz
S.W.R: Less than or equal to 1.5
Radiation Pattern: Omni-Directional
Connector: Ipex 4 generation
Radiator Material:Cu
Package included:
20pcs x antennas
2. FrSky XSR 2.4GHz 16CH ACCST Receiver S-Bus CPPM Output Support X9D X9E X9DP X12S
Feature
Number of channels: 16(S-Bus) : 8(CPPM)RSSI output: analog voltage output (0~3.3V)
Operating Range: >1.5km (Full Range)
Operating Current: 100mA@5V
Operating Voltage: 4 - 10.0V
Description
Weighing in at 4.3 grams (including connection cable) and smaller than the X4R, this little receiver is a great choice for micro multirotors. The XSR is SmartPort enabled and has S-bus as well as CPPM outputs. However we needed to give some things up so it could be smaller. The XSR does not support FBVS nor PWM and the antennas are soldered on instead of utilizing IPX connectors.3. Frsky XM Plus Mini Full Range Receiver Failsafe D16 Mode Support SBUS Up Compatible With Frsky X9D / X9D Plus X9E X12S Transmitter.
Feature
1. It's a full range receiver, similar range to X4R-SB and XSR, Much smaller size and lighter weight2. It's possible to direct solder RX to FC with header pins without wires (if FC supports it)
3. XM+ is even smaller than the LR1000 by FuriousFPV, great RX option for their micro quads (such as the Moskito70)
4. Only downside of XM+ RX is the lack of S.Port full telemetry (Smart Port), there is only RSSI telemetry. RSSI has a dedicated solder pad and it's also available on the 16th channel.
5. RSSI pin outputs PWM signal (0-3.3V). Please be aware that this signal should not be connected to MinimOSD directly, as it will give you 0% or 100% only. You will need a digital to analogue converter (low pass filter) to convert PWM to analogue voltage level.
Description
General This insanely tiny 2.4GHz diversity receiver available Package Including Frsky XM Plus receiver4. Frsky ACCST Taranis Q X7 2.4G 16CH RC Transmitter for FPV Racing Drones (Black)
Feature
Frsky Q X7 US Version( Mode II)Compatibility: FrSky X series, D series and V8-II series receivers (plus other receivers if an external module is used)
Doesn't come with battery and charger
Includes: Taranis Q X7 Transmitter - Neck Strap - User Manual
Description
Frsky have put their reliable and well-known frequency hopping ACCST technology into the new Taranis Q X7 radio system with addition of full telemetry. All the usual Taranis features are used in this radio such as Receiver Signal Strength Indicator (RSSI) alerts, Real-time Flight Data Logging and receiver matching. There is a new look case that comes in either black or white. Once again the excellent Quad Ball-Bearing Gimbals are used and it is up to you to determine what mode to set the radio to and also if you want self-centering spring loaded sticks (standard) or the usual stationary set throttle. The Taranis mixes the power of the "OPEN TX" open-source software with an ergonomic case with 6 programmable switches (4 x 3-position, 1 x 2-position, 1 x momentary) and two twist knobs. Set up your switches and controls how you want them. Alerts can be presented in the form of audio speech outputs, sound or vibration alerts making this extremely user-friendly. The MicroSD card slot offers unlimited model memory options, it also has a USB port for upgrades and to connect to a PC for adjusting settings. As well as this there is the ability to use all your model files from the older TARANIS X9D/X9D Plus/X9E making it easy to get the new system up and working. The FrSky Taranis Q X7 is a very versatile, cost effective radio.5. FrSky X4RSB 3/16CH Telemetry Receiver Full Range
Feature
RSSI (PWM) outputLighter weight and physically smaller than D8R-II & D6FR
Two selectable failsafe setting options - native failsafe or user programmable failsafe
S.Bus port is compatible with Futaba S.BUS servos and FrSky SBUS&CPPM compatible servo
External analog telemetry port (AD2)
Description
Description:- Brand name: FrSky
- Item name: FrSky X4RSB 3/16ch Telemetry Receiver
- Dimension: 40*22.5*6mm (L x W x H)
- Weight: 5.8g
- Operating Range: full range (>1.5km)
- Operating Voltage Range: 4.0~10V
- Operating Current: 100mA@5V
- Number of Channels: 3/16Ch (1~3ch from conventional channel outputs,1~16ch from SBUS channel)
- Compatibility: FrSky X-series Module (XJT etc.) Taranis X9D in D16 mode(X4RSB is not work with D-series Module)
6. Irctek 5pcs Frsky X4R X4RSB S6R XM XM+ Receiver Antenna 15cm New Version
Feature
5pcs Frsky X4rsb Receiver Antenna 15cm New Version, smaller IPEX4 connectorFit for new X4R X4RSB released in the second half of 2016, S6R / S8R / R-XSR / G-RX8 / XM / XM+ Receiver, XMPF3E flight control
Frsky original factory antenna, non replacement
Unique design, not compatible with other Receivers
XSR Receiver Antenna, please search B06XVMZ9TS
7. FrSky Taranis X9D Plus 16-channel 2.4ghz ACCST Radio Transmitter (Mode 2)
Feature
Taranis X9D Plus Transmitter(Mode 2) - US Type ChargerCarry Case and Receiver NOT included
Compatibility: FrSky X series,D series and V8-ll series receives
Channels: Up to 16 channels
Operating Voltage: 6 - 15V(2S,3S Lipos are acceptable)
Description
Model Name:Taranis X9D Plus EU(mode 2) Specifications: Number of Channels: Up to 16 channels Operating Voltage Range:6~15V (2S, 3S Lipos are acceptable) Operating Current: 260mA maximum (both RF module and backlit are on) Operating Temperature: -10~60 Backlight LCD Screen: 212*64, 2 color combinations for select Model Memories: 60 (extendable by SD card) Compatibility: FrSky X series, D series and V8-II series receivers (plus other receivers if an external module is used) Taranis X9D Plus-EU version is only compatible with X series receiver EU version. Features: Quad Ball Bearing Gimbals Receiver Match Audio Speech Outputs (values, alarms, settings, etc.) Real-time Flight Data Logging Receiver Signal Strength Indicator (RSSI) Alerts Super Low Latency Smart Port Supported Vibration Alerts. Notes and Warnings. Please connect the provided battery in the battery compartment before use. The six-cell NiMH battery is for use only in your TARANIS X9D Plus. Be sure to use the built-in battery charger to charge the battery. Be careful not to drop the battery. Don't pull the battery wires as this could produce,short-circuits and cause the battery to explode. Do not remove the battery from the TARANIS X9D Plus transmitter while the voltage warning is blinking as this could cause internal settings and memories to be destroyed. Do not use the transmitter if a "Backup Error" warning occurs. Be sure to turn off the Taranis X9D Plus before charging the battery. The Power Indicator LED will be on during charging, and be off after the charging is finished. Be sure to turn off the power of the transmitter before inserting or removing the MicroSD card. As the MicroSD card is a precision device, do not use excessive force when inserting If model data generated by a transmitter with a new software version is copied to an one with older software, the transmitter may not operate correctly. Before copying the model data, update the destination transmitter to the new software version. Do not expose the MicroSD card to dirt, moisture,water or fluids of any kind. Never remove the MicroSD card or turn off power while entering data. Never store the MicroSD card where it may be subject to strong static electricity or magnetic fields. Do not expose the MicroSD card to direct sunlight, excessive humidity or corrosive environments. Be certain to insert the MicroSD card in the correct direction.8. nidici 10pcs 2.4G IPEX4 Feeder Line Antenna for FRSKY X4R / X4RSB / S6R / D Series / TF Series Receiver
Feature
Connector TypeIPEX4Wire Material:RF0.81 silver plated
Cable length:15cm
Application: 2.4G remote control, monitor, model airplane, bluetooth etc
And suit for Frsky X4R/X4RSB/S6R/D series/TF Series receiver 2.4G Receiver
Description
X4R/X4RSB/S6R/D series/TF Series receiver 2.4G Receiver 150mm Compatible with long-range antennaA.Electrical Characteristics
Frequency: 2400 to 2500 MHz
SWR:less than 2.0
Antenna Gain: 2.0
Polarization: Linear
Impedance :50 Ohm
B.Material and Mechanical Characteristics
Cable Type:RF 113
Connector Pull Test:more than 2 Kg
C.Environmental
Operation Temperature :-40-+65
Storage Temperature:-40-+80
Notice: IPEX1 is for FrSky regular receiver(V series,D series and TF series)
IPEX4 is for FrSky new receiver( X4R/X4SB/S6R and etc)
This antenna is new thin type 150mm length for new production X4RSB, S6R receiver.
Length:15cm
Compatibilty: New X4RSB/X4R, and S6R receivers.
Attention:
1. FrSky Changed to New Antenna in X4RSB/X4R, S6R receivers .
2.New Antenna is SMALLER connector and Thinner Antenna Wire.
3.Same Length, and lighter compare with old version;
4.This antenna is thin type particular for new X4RSB, X4R and S6R receiver, it is not compatible with other receivers.
9. FrSky R-XSR Ultra Mini Redundancy Full Telemetry Receiver
Feature
Ultra mini size and light weightSupports redundancy function
IPEX connector, replaceable antennas
Switchable SBUS/ CPPM signal output
Support telemetry and Smart Port enabled
Description
FrSky ultra mini receiver R-XSR is the evolution of FrSky full range XSR receiver.
The R-XSR is a standalone receiver with all the functions of XSR, in addition, it's almost 1/3 size and 1/3 weight of XSR receiver.
Moreover, there redundancy function is integrated into this tiny receiver ensures the security, and the IPEX connector makes itmore convenient for you to replace antennas.
- Dimension: 16*11*5.4mm (L*W*H)
- Weight: 1.5g
- Number of channels: 16CH (1-16CH from SBUS channel, 1~8CH from CPPM channel)
- Operating Voltage Range: 4~10V
- Firmware Upgradable
- Compatibility: FrSky X Series modules and radios in D16 mode
10. FrSky 2.4G ACCST Taranis Q X7 16 Channels Transmitter White
Feature
Quad Ball Bearing GimbalsReal-time Flight Data Logging
Receiver Signal Strength Indicator (RSSI) Alerts
Audio Speech Outputs (values, alarms, settings, etc.) (1)
Model configuration files compatible with TARANIS X9D Plus
Description
This is the latest powerful radio system from FrSky, the Taranis Q X7. This is a lightweight feature packed reliable system and it comes in black or white color scheme. The radio includes a Haptic Vibration Feedback System which provides an alternative feedback system to the voice and sound alert warnings. This 16 channel radio has smooth ball bearing gimbals and is loaded with six switches and two knobs. It runs on OpenTX and files can be shared with the popular X9D Plus. The MicroSD card slot offers unlimited model memory options , it also has a USB port for upgrades and to connect to a PC for adjusting settings. Both sticks come with spring loaded return to center sticks, this makes changing from mode 1 to mode 2 extremely easy to set through the menu and the stick can quickly be set to a stationary throttle by unscrewing four screws and removing a spring. One of the best features of the Taranis Q X7 is its full telemetry capability, as well as RSSI signal strength feedback. Wheel and center enter button makes navigating the backlit menu easy and precise. Equipped with an audio jack output and trainer port as well. And of course a module bay for use with JR-type modules that can be used with other protocol receivers and with the use of a FrSky XJT module this radio can support up to 32-channels.
Specifications:- Model Name: Taranis Q X7
- Operating Voltage Range: 6~15V (2S, 3S Lipos are acceptable)
- Operating Current: 210mA maximum (both RF module and backlit are on)
- Operating Temperature: -10~45
- Backlight LCD Screen: 128*64 outdoor readable LCD
- Model Memories: 60 (extendable by SD card)
- Compatibility: FrSky X series, D series and V8-II series receivers (plus other receivers if an external module is used)
11. FrSky Taranis Compatible Receiver X4R 4-channel 2.4ghz ACCST&Telemetry
Feature
Smart Port enabledWith external Analog Telemetry port (AD2)
Lighter weight and physically smaller than X8R and X6R
With RSSI PWM output (0~3.3V) on board
FrSky Brand
Description
X4R receiver features 4 PWM outputs (normal servo) and now includes an option for CPPM output for feeding to flight controllers or other uses. CPPM carries 8 channels on a single servo wire. Smart Port and a traditional A2 port are all located on the side of the receiver and allow you to connect all sorts of great sensors to send data back to your FrSky radio.
Model Name:X4R Specifications
Dimension: 40*22.5*6mm (L*W*H)
Weight: 5.8g
Number of Channels: X4R-4ch from conventional channel outputs, without SBUS port X4RSB-3/16ch (1~3ch from conventional channel outputs, 1~16ch from SBUS channel)
Operating Voltage Range: 4.0~10V
Operating Current: 100mA@5V
Operating Range: full range (>1.5km) With RSSI output on board: PWM voltage output (0~3.3V)
Firmware Upgradeable
Compatibility: FrSky X-series Module (XJT etc. ) & Taranis X9D Plus in D16 mode (X4R / X4RSB is not work with D-series Module)
Features: Smart Port enabled With external Analog Telemetry port (AD2) Lighter weight and physically smaller than X8R and X6R With RSSI PWM output (0~3.3V) on board