If you looking for toggler anchors then you are right place. We are searching for the best toggler anchors on the market and analyze these products to provide you the best choice.
Reviews
1. TOGGLER SNAPTOGGLE BA Toggle Anchor with Bolts, Zinc-Plated Steel Channel, Made in US, 3/8" to 3-5/8" Grip Range, For 3/16"-24 UNC Fastener Size (Pack of 10)
Feature
Toggle anchor installs behind 3/8"- to 3-5/8"-thick hollow materials including gypsum board, drywall, and concrete block to provide a secure hold from within the mounting materialAnchor affixes to the wall before adding the bolt and fixture, allowing one-person installation and fixture changes
Made in USA, and includes 3/16"-24 UNC-threaded bolts
Ultimate tensile strength is 238 lb. in 1/2" drywall and 802 lb. in concrete block with a 3/16"-24 UNC bolt
Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations)
Description
The TOGGLER SNAPTOGGLE BA toggle anchor provides a secure hold from within various hollow materials 3/8" to 3-5/8" thick including gypsum board, drywall, and concrete block, includes 3/16"-24 UNC-threaded bolts, and is made in USA. The anchor channel will not rotate when installing the bolt, whether installing by hand or with a screw gun, and will stay in place if the bolt is removed to facilitate fixture and screw changes. If using bolts other than those supplied, the anchor accepts 3/16"-24 UNC metal bolts with a minimum length equal to the thickness of the item being fastened and the thickness of the mounting material plus 1/2". The SNAPTOGGLE anchor meets Federal Specification FF-B-588-D for Type V anchors.
The anchor consists of a corrosion-resistant zinc-plated steel anchor channel that inserts through a 1/2" drilled hole in walls, ceilings, or floors and installs against the back side of the mounting material; plastic straps attached to the channel that position it into place; and a plastic cap that slides down the straps and presses into the drilled hole firmly to lock the anchor channel in place behind the mounting material. Once the cap is set in place, the straps snap off by hand. The item being fastened affixes to the mounting material by inserting one of the included bolts through the item, into the drilled hole, and through the anchoring channel behind the material and tightening.
Specifications
Ultimate Tensile and Shear Strength Values
| Media | Drill Diameter | Bolt Description | Ultimate Tensile Strength Values | Ultimate Shear Strength Values |
| 1/2" Drywall | 1/2" | 3/16"-24 UNC zinc-plated steel | 238 lb. | 247 lb. |
| 5/8" Drywall | 1/2" | 3/16"-24 UNC zinc-plated steel | 356 lb. | 298 lb. |
| 1/2" Drywall with 25 Gauge Stud* | 1/2" | 3/16"-24 UNC zinc-plated steel | 412 lb. | Not Available |
| 5/8" Drywall with 25 Gauge Stud* | 1/2" | 3/16"-24 UNC zinc-plated steel | 462 lb. | Not Available |
| Concrete Block | 1/2" | 3/16"-24 UNC zinc-plated steel | 802 lb. | Not Available |
*Failure measured as breakage of drywall portion.
Warning: Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations). For more information, see the manufacturer's technical bulletin.
Anchors provide reinforcement to a fastener that would otherwise have insufficient hold in substrates such as concrete, brick, stone, drywall, or other materials for a particular application. The fastener may be included with or integrated into the anchor itself, or it may be sold separately. Anchors provide support through various methods, including expansion from within or behind the substrate or even adhesive compounds.
TOGGLER Anchor System manufactures wall anchors and toggle bolts. The company, founded in 1968, is headquartered in Norwalk, CT.
Whats in the Box?
- (10) TOGGLER SNAPTOGGLE BA toggle anchors
- (10) 3/16"-24 UNC bolts
2. TOGGLER SNAPTOGGLE BB Toggle Anchor, Zinc-Plated Steel Channel, Made in US, 3/8" to 3-5/8" Grip Range, For 1/4"-20 UNC Fastener Size (Pack of 100)
Feature
Toggle anchor installs behind 3/8"- to 3-5/8"-thick hollow materials including gypsum board, drywall, and concrete block to provide a secure hold from within the mounting materialAnchor affixes to the wall before adding the bolt and fixture, allowing one-person installation and fixture changes
Made in USA, and works with 1/4"-20 UNC-threaded metal bolts (sold separately)
Ultimate tensile strength is 265 lb. in 1/2" drywall and 1,080 lb. in concrete block with a 1/4"-20 UNC bolt
Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations)
Description
The TOGGLER SNAPTOGGLE BB toggle anchor provides a secure hold from within various hollow materials 3/8" to 3-5/8" thick including gypsum board, drywall, and concrete block, and is made in USA. The anchor requires a 1/4"-20 UNC-threaded metal bolt with a minimum length equal to the thickness of the item being fastened and the thickness of the mounting material plus 1/2". The anchor channel will not rotate when installing the bolt, whether installing by hand or with a screw gun, and will stay in place if the bolt is removed to facilitate fixture and screw changes. The SNAPTOGGLE anchor meets Federal Specification FF-B-588-D for Type V anchors.
The anchor consists of a corrosion-resistant zinc-plated steel anchor channel that inserts through a 1/2" drilled hole in walls, ceilings, or floors and installs against the back side of the mounting material; plastic straps attached to the channel that position it into place; and a plastic cap that slides down the straps and presses into the drilled hole firmly to lock the anchor channel in place behind the mounting material. Once the cap is set in place, the straps snap off by hand. The item being fastened affixes to the mounting material by inserting a bolt through the item, into the drilled hole, and through the anchoring channel behind the material and tightening.
Specifications
Ultimate Tensile and Shear Strength Values
| Media | Drill Diameter | Bolt Description | Ultimate Tensile Strength | Ultimate Shear Strength |
| 1/2" Drywall | 1/2" | 1/4"-20 UNC zinc-plated steel | 265 lb. | 241 lb. |
| 5/8" Drywall | 1/2" | 1/4"-20 UNC zinc-plated steel | 356 lb. | 324 lb. |
| 1/2" Drywall with 25 Gauge Stud* | 1/2" | 1/4"-20 UNC zinc-plated steel | 425 lb. | Not available |
| 5/8" Drywall with 25 Gauge Stud* | 1/2" | 1/4"-20 UNC zinc-plated steel | 464 lb. | Not available |
| Concrete Block | 1/2" | 1/4"-20 UNC zinc-plated steel | 1,080 lb. | Not available |
*Failure measured as breakage of drywall portion.
Warning: Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations). For more information, see the manufacturer's technical bulletin.
Anchors provide reinforcement to a fastener that would otherwise have insufficient hold in substrates such as concrete, brick, stone, drywall, or other materials for a particular application. The fastener may be included with or integrated into the anchor itself, or it may be sold separately. Anchors provide support through various methods, including expansion from within or behind the substrate or even adhesive compounds.
TOGGLER Anchor System manufactures wall anchors and toggle bolts. The company, founded in 1968, is headquartered in Norwalk, CT.
3. TOGGLER SnapSkru Self-Drilling Drywall Anchor, Pack of 20
Feature
with Screws, Glass-Filled Nylon, Made in US, For #6 to #10 Fastener SizesDescription
Self-drilling no pre-drilled hole required. Higher load-bearing capability and screw size range than other self-drilling drywall anchors. Built-in "positive-stop" prevents over-driving the anchor when using a screw gun or hand drill. Activate and lock with an audible "POP", providing positive feedback that they are installed correctly. Resist vibration and shock. Provide high pull-out resistance. Do not back out of the wall when the screw is removed. Can be removed easily, without damaging wall. Unique tip prevents "walking" to ensure accurate and easy drilling. When activated with a screw anchor opens with an audible pop locking the anchor on the wall. Drywall gypsum and its paper are kept in compression and thereby immediately reinforced. Built-in positive stop that prevents overdriving the anchor when using a screw gun. 20 pack Regular SnapSkru 3/8" - 5/8" drywall thickness #8 x 1-1/2" combo screws 1-1/4" + thickness of item being anchored #6, #7, #8 (preferred), #10 Self-drilling no pre-drilled hole required Regular: 0.62"dia. head, 5/16" dia., 1-5/8" length Higher load-bearing capability and screw size range than other self-drilling drywall anchors Built-in positive-stop prevents over-driving the anchor when using a screw gun or hand drill Activate and lock with an audible POP, providing positive feedback that they are installed correctly Resist vibration and shock Provide high pull-out resistance Do not back out of the wall when the screw is removed Can be removed easily, without damaging wall Unique tip prevents "walking" to ensure accurate and easy drilling When activated with a screw anchor opens with an audible pop locking the anchor on the wall Drywall gypsum & its paper are kept in compression & thereby immediately reinforced Built-in positive stop that prevents overdriving the anchor when using a screw gun.4. TOGGLER Toggle TB Residential Drywall Anchor with Screws, Polypropylene, Made in US, 3/8" to 1/2" Grip Range, For #6 to #14 Fastener Sizes (Pack of 20)
Feature
Residential drywall anchor provides a firm hold from within 3/8"- to 1/2"-thick drywallAnchor affixes to the wall before adding the bolt and fixture, allowing one-person installation and fixture changes
Made in USA, and includes #8 x 1-1/2" screws
Ultimate tensile strength is 143 lb. in 1/2" drywall with a #8 x 1-1/2" screw
Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations)
Description
The TOGGLER Toggle TB residential drywall anchor provides a firm hold in 3/8"- to 1/2"-thick drywall, includes #8 x 1-1/2" screws, and is made in USA. The anchor is made from polypropylene that resists corrosion, is nonconductive for anchoring electrical components, and is low-friction to facilitate screw installation. The anchor hammers into a 5/16" drilled hole until flush with the mounting material's surface. Before the screw can be inserted into the anchor to create a secure hold, the included key is used to open the anchor's wings behind the material. The fins on the anchor head grip the mounting material to prevent spinning when a screw is inserted, and the anchor will stay in place if the fastener is removed, facilitating fixture and screw changes. If using screws other than those supplied, the anchor accepts #6 to #14 size screws with a minimum thread length of 1-1/4". The Toggle TB anchor meets Federal Specification FF-B-588-D for Type IV anchors.
Specifications
Ultimate Tensile Strength Values
| Anchor | Drill Diameter | Screw Description | 1/4" Plywood | 1/2" Plywood | 3/8" Drywall | 1/2" Drywall | 5/8" Drywall |
| TA | 5/16" | #8 x 1-1/4" | 124 lb. | Not applicable | Not applicable | Not applicable | Not applicable |
| TB | 5/16" | #8 x 1-1/2" | Not applicable | 175 lb. | 97 lb. | 143 lb. | Not applicable |
| TC | 5/16" | #8 x 1-3/4" | Not applicable | Not applicable | Not applicable | Not applicable | 159 lb. |
Ultimate Shear Strength Values
| Anchor | Drill Diameter | Screw Description | 1/4" Plywood | 3/8" Drywall | 1/2" Drywall | 5/8" Drywall |
| TA | 5/16" | #8 x 1-1/4" | 265 lb. | Not applicable | Not applicable | Not applicable |
| TB | 5/16" | #8 x 1-1/2" | Not applicable | 126 lb. | 167 lb. | Not applicable |
| TC | 5/16" | #8 x 1-3/4" | Not applicable | Not applicable | Not applicable | 237 lb. |
Warning: Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations). For more information, see the manufacturer's technical bulletin.
Anchors provide reinforcement to a fastener that would otherwise have insufficient hold in substrates such as concrete, brick, stone, drywall, or other materials for a particular application. The fastener may be included with or integrated into the anchor itself, or it may be sold separately. Anchors provide support through various methods, including expansion from within or behind the substrate or even adhesive compounds.
TOGGLER Anchor System manufactures wall anchors and toggle bolts. The company, founded in 1968, is headquartered in Norwalk, CT.
Whats in the Box?
- (20) TOGGLER Toggle TB anchors
- (20) #8 x 1-1/2" screws
- (1) Setting key
5. 12 Pieces TOGGLER SNAPTOGGLE Drywall Anchor with included bolts for 1/4-20 Fastener size; holds 80 pounds each by TOGGLER
Feature
Toggle anchor installs behind 3/8"- to 3-5/8"-thick hollow materials including gypsum board, drywall, and concrete block to provide a secure hold from within the mounting materialAnchor affixes to the wall before adding the bolt and fixture, allowing one-person installation and fixture changes
Made in USA, and includes 1/4"-20 UNC-threaded bolts
Ultimate tensile strength is 265 lb. in 1/2" drywall and 1,080 lb. in concrete block with a 1/4"-20 UNC bolt (included)
Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations)
Description
Mount anything!The TOGGLER SNAPTOGGLE BB toggle anchor provides a secure hold from within various hollow materials 3/8" to 3-5/8" thick including gypsum board, drywall, and concrete block, includes 1/4"-20 UNC bolts, and is made in USA. The anchor channel will not rotate when installing the bolt, whether installing by hand or with a screw gun, and will stay in place if the bolt is removed to facilitate fixture and screw changes. If using bolts other than those supplied, the anchor accepts 1/4"-20 UNC metal bolts with a minimum length equal to the thickness of the item being fastened and the thickness of the mounting material plus 1/2". The SNAPTOGGLE anchor meets Federal Specification FF-B-588-D for Type V anchors.
The anchor consists of a corrosion-resistant zinc-plated steel anchor channel that inserts through a 1/2" drilled hole in walls, ceilings, or floors and installs against the back side of the mounting material; plastic straps attached to the channel that position it into place; and a plastic cap that slides down the straps and presses into the drilled hole firmly to lock the anchor channel in place behind the mounting material. Once the cap is set in place, the straps snap off by hand. The item being fastened affixes to the mounting material by inserting one of the included bolts through the item, into the drilled hole, and through the anchoring channel behind the material and tightening.
6. TOGGLER Toggle TB Residential Drywall Anchor with Screws, Polypropylene, Made in US, 3/8" to 1/2" Grip Range, For #6 to #14 Fastener Sizes (Pack of 5)
Feature
Residential drywall anchor provides a firm hold from within 3/8"- to 1/2"-thick drywallAnchor affixes to the wall before adding the bolt and fixture, allowing one-person installation and fixture changes
Made in USA, and includes #8 x 1-1/2" screws
Ultimate tensile strength is 143 lb. in 1/2" drywall with a #8 x 1-1/2" screw
Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations)
Description
The TOGGLER Toggle TB residential drywall anchor provides a firm hold in 3/8"- to 1/2"-thick drywall, includes #8 x 1-1/2" screws, and is made in USA. The anchor is made from polypropylene that resists corrosion, is nonconductive for anchoring electrical components, and is low-friction to facilitate screw installation. The anchor hammers into a 5/16" drilled hole until flush with the mounting material's surface. Before the screw can be inserted into the anchor to create a secure hold, the included key is used to open the anchor's wings behind the material. The fins on the anchor head grip the mounting material to prevent spinning when a screw is inserted, and the anchor will stay in place if the fastener is removed, facilitating fixture and screw changes. If using screws other than those supplied, the anchor accepts #6 to #14 size screws with a minimum thread length of 1-1/4". The Toggle TB anchor meets Federal Specification FF-B-588-D for Type IV anchors.
Specifications
Ultimate Tensile Strength Values
| Anchor | Drill Diameter | Screw Description | 1/4" Plywood | 1/2" Plywood | 3/8" Drywall | 1/2" Drywall | 5/8" Drywall |
| TA | 5/16" | #8 x 1-1/4" | 124 lb. | Not applicable | Not applicable | Not applicable | Not applicable |
| TB | 5/16" | #8 x 1-1/2" | Not applicable | 175 lb. | 97 lb. | 143 lb. | Not applicable |
| TC | 5/16" | #8 x 1-3/4" | Not applicable | Not applicable | Not applicable | Not applicable | 159 lb. |
Ultimate Shear Strength Values
| Anchor | Drill Diameter | Screw Description | 1/4" Plywood | 3/8" Drywall | 1/2" Drywall | 5/8" Drywall |
| TA | 5/16" | #8 x 1-1/4" | 265 lb. | Not applicable | Not applicable | Not applicable |
| TB | 5/16" | #8 x 1-1/2" | Not applicable | 126 lb. | 167 lb. | Not applicable |
| TC | 5/16" | #8 x 1-3/4" | Not applicable | Not applicable | Not applicable | 237 lb. |
Warning: Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations). For more information, see the manufacturer's technical bulletin.
Anchors provide reinforcement to a fastener that would otherwise have insufficient hold in substrates such as concrete, brick, stone, drywall, or other materials for a particular application. The fastener may be included with or integrated into the anchor itself, or it may be sold separately. Anchors provide support through various methods, including expansion from within or behind the substrate or even adhesive compounds.
TOGGLER Anchor System manufactures wall anchors and toggle bolts. The company, founded in 1968, is headquartered in Norwalk, CT.
Whats in the Box?
- (5) TOGGLER Toggle TB anchors
- (5) #8 x 1-1/2" screws
- (1) Setting key